Installation Guide

A new installation guide video is now available for our next-generation (blue graphic) self-healing films!

• Hydrogel screen protector film
• Microfiber cloth, optionally included with the film
• Plastic applicator, spatula, plastic card, or plastic scraper, optionally included with the film
• Screen cleaner or isopropyl alcohol, 70% or more concentrated, or a wet cleaning wipe

Step: Preparing the workspace

Make sure you have a clean and well-lit workspace. Avoid dusty and damp environments, as dust or moisture can negatively affect the installation result.

Step: Preparing the display

Turn off the device.

Thoroughly clean the display with a microfiber cloth and screen cleaner, isopropyl alcohol, or a wet cleaning wipe. Make sure the display is completely dry and free of dust before continuing.

Step: Preparing the hydrogel screen protector film

Separate the carrier layer from the hydrogel film. The easiest way is to gently bend the edge until the layers start to separate.

The separated hydrogel film consists of three layers:

• On the back side, there is a protective layer divided into two parts.
• On the front side, there is another protective layer.
• The actual hydrogel film is located between these protective layers.

If your film includes auxiliary stickers, attach them to two corners of the bottom protective layer so that you can bend the film back more easily in the next step.

Do not remove any protective layer at this stage.

Do not turn the film over. The bottom side must remain in the same position as it was on the carrier layer. The bottom side is the side with the two-part protective layer.

Step: Applying the hydrogel screen protector film to the display

Place the hydrogel screen protector film on the device’s display in the same orientation as it was removed from the carrier layer.

Do not apply pressure yet. Gently place the film on the screen and adjust it into the correct position. If necessary, carefully lift it and reposition it.

Once the film is correctly aligned, use the plastic applicator to press the film onto the display along the central guide line.

Bend back one side of the film so that the bottom protective layer becomes exposed. Then smoothly apply the film to the display while gradually removing the bottom protective layer. Repeat the same process on the other side.

After the bottom protective layer has been removed, the film can no longer be repositioned without damaging it.

For films with blue graphics, the bottom protective layer is transparent.

Step: Removing air bubbles

If air bubbles appear during installation, use the applicator to gently push them out from under the film. Work slowly and carefully to avoid creating new bubbles or damaging the film.

Move the applicator along the edges as well, so that the film adheres firmly to the entire display.

If you notice small particles or air bubbles that cannot be removed, it means that dust or dirt remained on the display, or the screen was not cleaned thoroughly enough during the first step.

Step: Final adjustment

Once the film is correctly positioned and the bubbles have been removed, go over the film again with the applicator using light pressure. This helps ensure proper contact between the film and the display.

Step: Completion and removing the top protective layer

After successful installation, let the film rest for at least a few hours so that it can fully adhere to the screen.

The film has an outer protective layer. Carefully remove it, starting from one corner. You can use the auxiliary stickers for this: attach a sticker to one corner and gently peel off the protective layer.

Small air bubbles, lines, or marks that may appear during installation usually disappear or heal by themselves within 24–48 hours.

Congratulations!

The hydrogel screen protector film is now properly applied to your device’s display. Check that the film adheres evenly, that there are no major air bubbles, and that it is correctly aligned. You can now safely use your device with enhanced protection against scratches and fingerprints.

Installation of camera lens protector film

Thoroughly clean the camera lenses and the camera island.

Remove dust and dirt carefully from the camera lens. Place the device on a flat, non-slip surface.

Using the auxiliary sticker, remove the top protective layer from the film. If the film and the sticker do not separate on the first attempt, press the sticker more firmly.

Place the auxiliary sticker back onto the hydrogel film from which the top protective layer has already been removed. Then use the sticker to lift the hydrogel film from the carrier layer.

Make sure that no dust or dirt gets onto the back side of the hydrogel film.

Apply the protector film to the camera lens using the auxiliary sticker, then remove the sticker. If the film does not stay on the lens, press it down more firmly.

Repeat the same process for all camera lenses.

Installation of the camera island film

The process is the same. Remove the top protective layer, then use the auxiliary sticker to apply the hydrogel film to the camera island.

If installed correctly, small air bubbles will disappear within 72 hours.

If the auxiliary sticker is missing, you can use any sticker, tweezers, or adhesive tape that sticks firmly enough to the protective layer.

Video guide: